![crown trick menus crown trick menus](https://www.gourmandize.com/uploads/article/06/a9/c0/ac/5886d444fe6320be9ccf398a7c4ec9399557a47b-2.jpg)
If you have anything that's not a white wall, I'd recommend using a primer for this. Step 4: Paint the gap.įinally, give the gap between your molding pieces a few coats of trim paint to make it look like one piece! Our builder left our remaining trim paint (Sherwin Williams' Snowbound in semi-gloss) for us, which has been great for touch-ups and little projects like this. Caulk is an easy way to fix those little gaps in molding pieces. However, check to make sure no nail holes need to be caulked and that there aren't any gaps in the trim molding that need to be evened out. There's no need to caulk above the molding (you can't really see it). I'd like to give you a better tool to use for getting caulk even, but I've yet to find one! ? To take off any excess caulk and smooth it, you can gently rub over the finished caulking (before it dries) with a wet paper towel. Work your way around the room until this step is done I recommend going in a circle to avoid having to make too many correction cuts and re-measures later on. Cut an angle in the other end of your molding to complement the corner of the wall (so, more than likely, facing out). Make note of how that 45 degree angle will need to face – if your angle faces the wall (like the one you see above), cut a 45 degree angle that faces you to fit into that space, like a puzzle. When in doubt, go with the longer measurement you can always make a second cut to size it down if needed. Remember that angle we put on the second side of the molding? Measure from the opposite corner of your wall to the longest edge of where you'll need to cut the next piece. Sometimes the scrap can kind of get stuck if you put too many nails in before removing it.ĭepending on the size of the wall and the size of your molding piece, you'll more than likely need to add more than one piece per wall. Hold up the scrap wood just to get your molding in place put a couple of nails in to align the molding correctly, then remove the wood scrap and finish nailing in place.
![crown trick menus crown trick menus](https://www.motorbiscuit.com/wp-content/uploads/2021/04/Toyota-Crown-Kluger-1.jpeg)
Really, any size board can be used to create the gap it's kind of a personal preference, but I thought the gap this created was substantial without being overdone.
![crown trick menus crown trick menus](https://10619-2.s.cdn12.com/m0/w1200/menu-The-Crown.jpg)
Position the corner side snugly in the corner of your wall and use a piece of 1×2″ wood to create an even gap between the bottom of your existing molding and the new molding. (This post assumes you already have some kind of molding installed if not, this project be done without, it just won't have the same finished effect.) Step 2: Cut angles and attach bottom molding.įirst off, the easiest and probably most effective part of this whole project: actually adding the width to your molding.
#CROWN TRICK MENUS HOW TO#
How to Install DIY Faux Crown Molding Step 1: Buy your supplies.
#CROWN TRICK MENUS UPGRADE#
I smile every time I walk by our dining room now – and I'm totally planning on doing this in our bedroom (and possibly the living room) as well now! Let's take a look at how easy (and inexpensive) this upgrade can be. The final results of this DIY faux crown molding project are more beautiful than I even pictured. I think that, if I had known how easy DIY faux crown molding was to install, I would have done it as soon as we moved in! Doing a whole room of crown molding “beef-up” only took a few hours (spread out over a few days). We're now three years into living in our home – and I'm just now getting around to putting in the thick crown molding I've wanted from day 1.